Fdisk.txt --------- Dit document geeft enige uitleg over het gebruik van het programma fdisk, dat tijdens de installatie gebruikt kan worden om de harde schijf in partities te verdelen. Hoewel het programma doorgaat voor "Spartaans" en beginnende gebruikers de schrik van hun leven bezorgt, valt het in de praktijk best mee. En het is nog altijd een van de meest robuuste partitie-programma's die er in omloop zijn. Fdisk heet de gebruiker welkom met de volgende boodschap: The number of cylinders for this disk is set to 2491. There is nothing wrong with that, but this is larger than 1024, and could in certain setups cause problems with: 1) software that runs at boot time (e.g., old versions of LILO) 2) booting and partitioning software from other OSs (e.g., DOS FDISK, OS/2 FDISK) Command (m for help): Fdisk valt meteen met de deur in huis in de vorm van de een of andere vage foutmelding! De beginnende Linux-gebruiker begint zich af te vragen wat er nou eigenlijk mis was met W*nd*ws.. En wat is er met mijn harddisk aan de hand?! Antwoord: er is helemaal niet aan de hand. Fdisk lijdt aan een stuk ouderwetse "verbosity" (breedsprakerigheid), stammend uit een tijd toen systeembeheerders nog geinteresseerd waren in het exacte aantal schijfsectoren e.d.; IEDERE moderne schijf heeft meer dan 1024 sectoren, en voor die problemen met boot loaders is een ruime voorraad oplossingen voorhanden.. De volgende regel zaait in eerste instantie alleen nog maar meer verwarring: Command (m for help): Het aanknopingspunt is "m": na het indrukken van deze toets verschijnt er inderdaad een lijstje van commentaar voorziene commando's. Hier kan Fdisk weer niet van breedsprakerigheid worden beschuldigd, maar wie even de tijd neemt om de zaak te bestuderen, moet de relevante commando's er in no time uit weten te halen. Wat fdisk moeilijk maakt zijn niet zozeer de 1-letter commando's (het "gebruikersvriendelijke" parted met zijn "hele zinnen" is stukken lastiger), maar de volgorde waarin en vooral de snelheid waarmee e.e.a. plaatsvindt. Wat dat betreft vergt fdisk zowel van de beginnende als van de meer ervaren gebruiker de nodige concentratie en zorgvuldigheid. Het is geen slecht idee om na iedere actie [dus achter de "Command (m for help):" prompt] even m.b.v. het commando "p" (print) de resultaten te bekijken; daardoor verloopt het gehele proces een stuk overzichtelijker. Voor wie echt even door de bomen het bos niet meer ziet, is er het "q" (quit) commando, waarmee afgesloten wordt, zonder dat er in de partitietabel iets verandert. Bedenk ook dat het "m" commando altijd klaar staat achter de fdisk prompt. De lijst die door "m" gepresenteerd wordt, ziet er als volgt uit: a toggle a bootable flag b edit bsd disklabel c toggle the dos compatibility flag d delete a partition l list known partition types m print this menu n add a new partition o create a new empty DOS partition table p print the partition table q quit without saving changes s create a new empty Sun disklabel t change a partition's system id u change display/entry units v verify the partition table w write table to disk and exit x extra functionality (experts only) Het heeft weinig zin om de diverse commando's hier een voor een te gaan behandelen; voor details zie de fdisk manual beneden. Hier volgt een overzicht van de meest voorkomende acties en de volgorde van te werk gaan daarbij. 1. Print the partition table: "p" "p" laat een overzicht van de huidige partitie-indeling zien, inclusief de tot nu toe aangebrachte wijzigingen: Disk /dev/hdb: 255 heads, 63 sectors, 2491 cylinders Units = cylinders of 16065 * 512 bytes Device Boot Start End Blocks Id System /dev/hdb1 * 1 31 248976 83 Linux /dev/hdb2 32 37 48195 83 Linux /dev/hdb3 38 298 2096482+ 83 Linux /dev/hdb4 299 2491 17615272+ f Win95 Ext'd (LBA) /dev/hdb5 299 1349 8442126 83 Linux /dev/hdb6 1350 2193 6779398+ 83 Linux /dev/hdb7 2194 2442 2000061 83 Linux /dev/hdb8 2443 2491 393561 83 Linux Partities 1 t/m 3 zijn primaire partities, 4 is een extended (Ext'd) partitie, en 5 t/m 8 zijn logische partities binnen de extended partitie. Het verschil tussen primaire en extended partities is nergens aan te zien; door "x" (extra functionality) te kiezen en vervolgens "e" (list extended partitions) worden de nummers van de extended en logische partities zichtbaar gemaakt, mocht dat nodig zijn (al zal get gepresenteerde overzicht even schrikken zijn;-). [Ook hier is "m" weer voor- handen, "r" is terug naar hoofdmenu]. N.B. Negeer foutmeldingen in de trant van "Partition X does not end on a cylinder boundary". Ook hier weer: niets aan de hand! 2. Delete a partition: "d" Als er geprobeerd wordt een nieuwe partitie te maken, terwijl de hele schijf al in partities verdeeld is, verschijnt de melding: "No free sectors available". Om nieuwe partities te kunnen maken moeten er dus eerst een of meer bestaande verwijderd worden (fdisk kent geen "resize" optie, in ieder geval geen makkelijke). > Command (m for help): d > Partition number (1-8): 8 > Command (m for help): p Resultaat: ---------- Disk /dev/hdb: 255 heads, 63 sectors, 2491 cylinders Units = cylinders of 16065 * 512 bytes Device Boot Start End Blocks Id System /dev/hdb1 * 1 31 248976 83 Linux /dev/hdb2 32 37 48195 83 Linux /dev/hdb3 38 298 2096482+ 83 Linux /dev/hdb4 299 2491 17615272+ f Win95 Ext'd (LBA) /dev/hdb5 299 1349 8442126 83 Linux /dev/hdb6 1350 2193 6779398+ 83 Linux /dev/hdb7 2194 2442 2000061 83 Linux Partitie 8 is verdwenen uit de partitietabel; d.w.z. uit de kopie in het geheugen van de PC: zolang er niet het commando "w" (write table to disk and exit) wordt gegeven, is alles wat zich binnen fdisk afspeelt volkomen veilig! Partities kunnen alleen maar 1 voor 1 verwijderd worden. Een uitzondering vormen de logische partities: als de extended partitie verwijderd wordt, terwijl er nog logische partities in aanwezig zijn, worden deze automatisch en zonder waarschuwing (!!) eveneens verwijderd. Vandaar dat het slim is om tussen de verschillende acties door steeds even een "p" te geven.. 3. Add a new partition: "n" > Command (m for help): n > Command action > e extended > p primary partition (1-4) Dit zal wel duidelijk zijn: er wordt gevraagd of er een primaire of extended partitie gemaakt moet worden, en er wordt meteen even bij verteld dat een primaire partitie nooit een hoger nummer dan 4 kan krijgen (omdat de "echte" partitietabel in het MBR slechts 4 ingangen heeft). Ons antwoord: p > Partition number (1-4): 1 > Partition 1 is already defined. Delete it before re-adding it. (Bovenstaande melding verschijnt bij een poging een reeds bestaande partitie te creeeren. Nieuwe poging: > Command (m for help): n > Command action > e extended > p primary partition (1-4) p > Partition number (1-4): 3 > First cylinder (38-2491, default 38): Antwoord: Omdat het gebruikelijk is om van voren naar achteren te werken (of van laag naar hoog), is de standaardwaarde voor de eerste cylinder vrijwel altijd goed. > Last cylinder or +size or +sizeM or +sizeK (.., default..): De standaarwaarde is hier: "alle overgebleven schijfruimte". Hooguit geschikt voor de laatste partitie dus. Een cylinder- nummer opgeven ligt niet erg voor de hand, in de meeste gevallen zal het een partitiegrootte in MB's worden, bijv: +2000MB (technisch gesproken is dit iets anders dan "2GB" [2048MB], maar voor dagelijks gebruik kan 1000MB als 1GB gelden) N.B. Het commando "p" laat partitiegrootes in "1024k blocks" zien, +500M wordt dan: 514080, of iets in die richting (fdisk rondt af naar cylindergrenzen). Het creeeren van extended en logische partities gaat op een vergelijkbare manier: > Command (m for help): n > Command action > e extended > p primary partition (1-4) > Partition number (1-4): 4 Er waren nog geen extended of logische partities, dus wordt dit de extended partitie die in de "echte" partitietabel komt te staan. Daarom krijgt deze partitie een nummer van 1-4. > First cylinder (102-2491, default 102): > Last cylinder or +size or +sizeM or +sizeK (.., default..): In dit geval is het wel de bedoeling dat alle overgebleven schijfruimte wordt gebruikt (tenzij niet alle primaire partities toegewezen zijn, en er ruimte voor een nieuwe moet overblijven, maar laten we de zaken eenvoudig houden..): 2 x dus. Als er een extended partitie aanwezig is, kunnen er logische partities in toegewezen worden. Als alle 4 de primaire partities toegewezen zijn, is het overbodig naar "extended of primaire" partitie te vragen: > Command (m for help): n > First cylinder (102-2491, default 102): > Last cylinder or +size or +sizeM or +sizeK (.., default..): +1500M Het verhaal zal intussen wel duidelijk zijn. Het zal ook duidelijk zijn dat het bij fdisk vrij makkelijk is om fouten en vergissingen te maken. In dat geval: geen nood, gewoon de betreffende partitie deleten en opnieuw creeeren. (Nog een reden om na iedere actie even de resultaten te controleren m.b.v. een "p"). 4. Change a partition's system id: "t" De System ID geeft aan op welke manier een partitie geformatteerd is (en dus hoe de data op de partitie gelezen dienen te worden). Voor schoolLAN/Linux zijn slechts twee System ID's van belang: 82 Linux swap 83 Linux Omdat de partities m.b.v. fdisk en dus in een Linux omgeving worden gecreeerd, wordt automatisch "83 Linux" gekozen. Alleen de System ID van de swap partitie moet dus nog even veranderd worden: > Command (m for help): t > Partition number (1-8): 3 > Hex code (type L to list codes): 82 > Changed system type of partition 3 to 82 (Linux swap) (Wie een indrukwekkende lijst van ondersteunde partitie-types wil zien, kan eerst een "l" invoeren; dit kan overigens ook vanuit het hoofdmenu). Een "p" laat zien dat de waarde voor deze partitie in het veld "Id" inderdaad veranderd is in 82. N.B. Het commando "a" (toggle a bootable flag) is voor Linux systemen van geen enkel belang. 5. Write table to disk and ext: "w" Quit without saving changes: "q" Als het zeker is dat alles goed staat ("p"!!), kan de nieuwe partitietabel naar de schijf geschreven worden m.b.v. het commando "w". DE BESTAANDE PARTITIE-INDELING GAAT HIERBIJ ONHERROEPELIJK VERLOREN. D.w.z. dat data in "oude" partities, die uit de partitietabel verwijderd zijn, niet zonder veel inspanning en/of handigheid weer teruggehaald kunnen worden. In de praktijk kunnen ze als verloren beschouwd worden. Bij twijfel kan het programma altijd m.b.v. het commando "q"; de oude partitietabel blijft dan in stand. Mochten er nog vragen rijzen, dan biedt de fdisk manual beneden hopelijk de nodige aanknopingspunten: FDISK(8) Linux Programmer's Manual FDISK(8) NAME fdisk - Partition table manipulator for Linux SYNOPSIS fdisk [-u] [-b sectorsize]device fdisk -l [-u] [-b sectorsize] [device ...] fdisk -s partition ... fdisk -v DESCRIPTION Hard disks can be divided into one or more logical disks called partitions. This division is described in the par­ tition table found in sector 0 of the disk. In the BSD world one talks about `disk slices' and a `disklabel'. Linux needs at least one partition, namely for its root file system. It can use swap files and/or swap parti­ tions, but the latter are more efficient. So, usually one will want a second Linux partition dedicated as swap par­ tition. On Intel compatible hardware, the BIOS that boots the system can often only access the first 1024 cylinders of the disk. For this reason people with large disks often create a third partition, just a few MB large, typi­ cally mounted on /boot, to store the kernel image and a few auxiliary files needed at boot time, so as to make sure that this stuff is accessible to the BIOS. There may be reasons of security, ease of administration and backup, or testing, to use more than the minimum number of parti­ tions. fdisk (in the first form of invocation) is a menu driven program for creation and manipulation of partition tables. It understands DOS type partition tables and BSD or SUN type disklabels. The device is usually one of the following: /dev/hda /dev/hdb /dev/sda /dev/sdb (/dev/hd[a-h] for IDE disks, /dev/sd[a-p] for SCSI disks, /dev/ed[a-d] for ESDI disks, /dev/xd[ab] for XT disks). A device name refers to the entire disk. The partition is a device name followed by a partition number. For example, /dev/hda1 is the first partition on the first IDE hard disk in the system. IDE disks can have up to 63 partitions, SCSI disks up to 15. See also /usr/src/linux/Documentation/devices.txt. A BSD/SUN type disklabel can describe 8 partitions, the third of which should be a `whole disk' partition. Do not start a partition that actually uses its first sector (like a swap partition) at cylinder 0, since that will destroy the disklabel. An IRIX/SGI type disklabel can describe 16 partitions, the eleventh of which should be an entire `volume' partition, while the ninth should be labeled `volume header'. The volume header will also cover the partition table, i.e., it starts at block zero and extends by default over five cylinders. The remaining space in the volume header may be used by header directory entries. No partitions may overlap with the volume header. Also do not change its type and make some file system on it, since you will lose the partition table. Use this type of label only when working with Linux on IRIX/SGI machines or IRIX/SGI disks under Linux. A DOS type partition table can describe an unlimited num­ ber of partitions. In sector 0 there is room for the description of 4 partitions (called `primary'). One of these may be an extended partition; this is a box holding logical partitions, with descriptors found in a linked list of sectors, each preceding the corresponding logical partitions. The four primary partitions, present or not, get numbers 1-4. Logical partitions start numbering from 5. In a DOS type partition table the starting offset and the size of each partition is stored in two ways: as an abso­ lute number of sectors (given in 32 bits) and as a Cylin­ ders/Heads/Sectors triple (given in 10+8+6 bits). The for­ mer is OK - with 512-byte sectors this will work up to 2 TB. The latter has two different problems. First of all, these C/H/S fields can be filled only when the number of heads and the number of sectors per track are known. Sec­ ondly, even if we know what these numbers should be, the 24 bits that are available do not suffice. DOS uses C/H/S only, Windows uses both, Linux never uses C/H/S. If possible, fdisk will obtain the disk geometry automati­ cally. This is not necessarily the physical disk geometry (indeed, modern disks do not really have anything like a physical geometry, certainly not something that can be described in simplistic Cylinders/Heads/Sectors form), but is the disk geometry that MS-DOS uses for the partition table. Usually all goes well by default, and there are no prob­ lems if Linux is the only system on the disk. However, if the disk has to be shared with other operating systems, it is often a good idea to let an fdisk from another operat­ ing system make at least one partition. When Linux boots it looks at the partition table, and tries to deduce what (fake) geometry is required for good cooperation with other systems. Whenever a partition table is printed out, a consistency check is performed on the partition table entries. This check verifies that the physical and logical start and end points are identical, and that the partition starts and ends on a cylinder boundary (except for the first parti­ tion). Some versions of MS-DOS create a first partition which does not begin on a cylinder boundary, but on sector 2 of the first cylinder. Partitions beginning in cylinder 1 cannot begin on a cylinder boundary, but this is unlikely to cause difficulty unless you have OS/2 on your machine. A sync() and a BLKRRPART ioctl() (reread partition table from disk) are performed before exiting when the partition table has been updated. Long ago it used to be necessary to reboot after the use of fdisk. I do not think this is the case anymore - indeed, rebooting too quickly might cause loss of not-yet-written data. Note that both the kernel and the disk hardware may buffer data. DOS 6.x WARNING The DOS 6.x FORMAT command looks for some information in the first sector of the data area of the partition, and treats this information as more reliable than the informa­ tion in the partition table. DOS FORMAT expects DOS FDISK to clear the first 512 bytes of the data area of a parti­ tion whenever a size change occurs. DOS FORMAT will look at this extra information even if the /U flag is given -- we consider this a bug in DOS FORMAT and DOS FDISK. The bottom line is that if you use cfdisk or fdisk to change the size of a DOS partition table entry, then you must also use dd to zero the first 512 bytes of that par­ tition before using DOS FORMAT to format the partition. For example, if you were using cfdisk to make a DOS parti­ tion table entry for /dev/hda1, then (after exiting fdisk or cfdisk and rebooting Linux so that the partition table information is valid) you would use the command "dd if=/dev/zero of=/dev/hda1 bs=512 count=1" to zero the first 512 bytes of the partition. BE EXTREMELY CAREFUL if you use the dd command, since a small typo can make all of the data on your disk useless. For best results, you should always use an OS-specific partition table program. For example, you should make DOS partitions with the DOS FDISK program and Linux partitions with the Linux fdisk or Linux cfdisk program. OPTIONS -b sectorsize Specify the sector size of the disk. Valid values are 512, 1024, or 2048. (Recent kernels know the sector size. Use this only on old kernels or to override the kernel's ideas.) -l List the partition tables for the specified devices and then exit. If no devices are given, those men­ tioned in /proc/partitions (if that exists) are used. -u When listing partition tables, give sizes in sec­ tors instead of cylinders. -s partition The size of the partition (in blocks) is printed on the standard output. -v Print version number of fdisk program and exit. BUGS There are several *fdisk programs around. Each has its problems and strengths. Try them in the order cfdisk, fdisk, sfdisk. (Indeed, cfdisk is a beautiful program that has strict requirements on the partition tables it accepts, and produces high quality partition tables. Use it if you can. fdisk is a buggy program that does fuzzy things - usually it happens to produce reasonable results. Its single advantage is that it has some support for BSD disk labels and other non-DOS partition tables. Avoid it if you can. sfdisk is for hackers only - the user inter­ face is terrible, but it is more correct than fdisk and more powerful than both fdisk and cfdisk. Moreover, it can be used noninteractively.) The IRIX/SGI type disklabel is currently not supported by the kernel. Moreover, IRIX/SGI header directories are not fully supported yet. The option `dump partition table to file' is missing. Linux 2.0 11 June 1998 1