[NLUUG]   Welcome to ftp.nluug.nl
Current directory: /pub/NetBSD/misc/UFS2ea/
Current bandwidth utilization 2237.85 Mbit/s
Bandwidth utilization bar
Contents of README:
On April 18, 2020, extended attribute support was added to UFS2 in
NetBSD-current, but that unfortunately this change made UFS2 dangerously
incompatible with UFS2 from previous NetBSD releases, so it was necessary
to remove extended attribute support from the UFS2 format that was
recognized by previous releases.  UFS2 extended attributes will only
be supported in NetBSD by a new UFS2 variant called "UFS2ea".

If your NetBSD-current system has UFS2 file systems and was built from
a source tree from between April 18, 2020 and September 23, 2022,
then you should use a special procedure to upgrade to a later
NetBSD-current, or to NetBSD 10 or later.


If you want to have the option of preserving any extended attributes
in UFS2 file systems (including ACLs), then you must download
and compile this utility:

cc -o ufs2ea-flip ufs2ea-flip.c

Put the resulting "ufs2ea-flip" executable somewhere in your root file system.
Putting it directly in the root directory is fine.

If you do not want to preserve any extended attributes that may have been
created in UFS2 file systems then you do not need the ufs2ea-flip utility.

Then follow these steps:

1. Install your new kernel and userland.
   In particular, you need the new version of /sbin/fsck_ffs.
   If your existing -current version is too old then the new
   fsck_ffs may require a new /lib/libc.so* and possibly other things.

2. Reboot your system into single-user mode.
   It is important to do an orderly reboot so that file systems
   are unmounted cleanly.
   Do not remount the root file system read/write or
   mount any other file systems yet.

3. Run a forced "fsck -p" of each UFS2 file system, eg.
	fsck -fp /dev/rwd0a
	fsck -fp /dev/rwd0e

4. If the new fsck says that your UFS2 file systems are all fine,
   then it is safe to exit single-user mode and let the system
   continue the normal boot process.

   However, if the new fsck reports this message for any file system:
   then that file system has had extended attributes set on one or more files,
   and you must decide whether to preserve or discard these extended attributes.

   Discarding extended attributes will lose this information forever,
   and each file that has extended attributes removed will also
   have the permission bits of the file's mode cleared,
   removing all access to the file (except by root).
   This is because the extended attributes might have been intended to
   contain an ACL, so removing all permissions avoids allowing access
   to the file by a process that should not have had any access.

   Preserving extended attributes avoids the downsides of discarding them,
   but this also converts the file system to the UFS2ea format, which is
   completely unrecognized by earlier NetBSD versions.  It is possible to
   convert a UFS2ea file system back to UFS2, but this also requires
   removing all extended attributes and removing access permissions
   to affected files.

   To discard extended attributes and keep a UFS2 file system in UFS2 format,
   run a forced full fsck, eg.
	fsck -fy /dev/rwd0a

   To preserve extended attributes and convert a UFS2 file system to UFS2ea
   format, run the ufs2ea-flip utility that you built earlier on the
   character device containing the file system, eg.
	/ufs2ea-flip /dev/rwd0a

   The ufs2ea-flip utility will verify that the given device contains a
   UFS2 file system and ask for confirmation before converting the file system
   to UFS2ea format while preserving extended attributes.  Running a
   forced full fsck after using this utility is strongly recommended.

5. After all UFS2 file systems are processed, if you have converted
   your root file system to UFS2ea then you should reboot.
   Otherwise you can exit the single-user shell and allow the system
   to continue the normal boot process.

After this procedure, your system should be ready for use.

Icon  Name                    Last modified      Size  
[DIR] Parent Directory - [TXT] README 24-Sep-2022 22:10 3.9K [TXT] ufs2ea-flip.c 23-Sep-2022 15:12 3.4K

NLUUG - Open Systems. Open Standards
Become a member and get discounts on conferences and more, see the NLUUG website!